Why Won’t My Interior Door Close Properly? Causes and Fixes for New Jersey Homes
Most interior doors that won’t close are caused by one of four things: loose or sagging hinges, seasonal swelling from humidity, a misaligned latch or strike plate, or a frame that has shifted. The fastest way to tell which one you have is to look at where the door touches the frame before you touch any tools.
Deft Craftsman provides door repair and adjustment for homeowners, renters, property managers and commercial clients across North and Central New Jersey. This guide explains how the problem is diagnosed, which fixes are straightforward, and when a “sticky door” is a sign of something bigger.
First, figure out what “won’t close” means
These are different problems with different fixes:
The door rubs or binds against the frame or floor as it closes.
The door closes but won’t latch. The latch bolt misses the strike plate opening.
The door bounces back or won’t stay closed.
The door rattles once closed, which is the opposite problem (too much play).

Where the door touches tells you why
Look for scuffed paint, shiny worn spots, or a gap that narrows to nothing. A sheet of paper slipped between the door and frame will show where it grips.
What you see | Most likely cause |
Top corner on the latch side rubs | Sagging upper hinge or loose hinge screws |
Entire latch edge rubs | Swollen door or paint buildup on the edge |
Rubbing near the hinges | Hinge recess (mortise) too shallow, paint in the mortise, or loose hinge |
Bottom corner drags | New flooring or carpet, or a loose lower hinge |
Latch misses the strike | Strike plate misaligned from slight sag |
Several doors stick at once | Humidity, or possibly settling (see below) |
Common causes of a door that won’t close
1. Loose hinge screws. This is the most common cause. The top hinge carries most of the door’s weight, and its screws can loosen in the soft jamb wood over years of use. Even a small amount of sag makes the opposite top corner bind.
2. Humidity swelling. Wood absorbs moisture and swells, and doors tighten during humid stretches. New Jersey summers are humid, so doors that stick from June through September and loosen by winter are usually reacting to seasonal moisture. EPA guidance recommends keeping indoor relative humidity below 60 percent, ideally 30 to 50 percent. A basement dehumidifier, or running bathroom and kitchen exhaust fans, can help more than any carpentry.
3. Paint buildup. Doors repainted several times, especially in older homes, can gain enough film on the edges and in the hinge recesses to bind. Rental turnover repainting is a frequent culprit.
4. New flooring. Thicker flooring or carpet pad raises the floor under the door. The door then drags at the bottom and needs trimming or the floor transition needs adjusting.
5. Misaligned latch or strike plate. If the door closes freely but won’t catch, the strike plate may sit a fraction of an inch off. Often the real cause is hinge sag, so fixing the hinge fixes the latch.
6. Warped door. A warped slab won’t sit flat in the frame. Hollow-core doors are more prone to this than solid-core doors, and it often can’t be fully corrected.
7. Frame or house movement. If the frame itself is out of square, the problem is not the door.
What a professional checks first
When Deft Craftsman evaluates a door that won’t close, the first question is whether the door or the frame is the problem. The usual order:
Check the gap (the “reveal”) around the door. It should be fairly even, commonly around 1/8 inch on the top and sides.
Test every hinge for movement, especially the top one.
Look for paint in the hinge recesses and on the door edges.
Check whether the floor, flooring height, or season changed recently.
Only then decide whether to remove material from the door.
The key point: diagnose before you plane. A door trimmed in August to fit the frame can leave a visible gap in January, when the wood shrinks back. And many doors are trimmed unnecessarily when loose hinge screws were the real problem.
A Livingston example: she called for a new door, and the fix was a hinge adjustment
In our work across New Jersey, we often see homeowners reach for replacement before anyone has checked what is actually wrong with the door.
A Livingston homeowner called us asking for a new interior door. It wouldn’t close properly, and she assumed replacement was the only answer.
Before quoting a new door, we looked at how the existing door was sitting in the frame. The door itself was fine. The problem was in the hinges, and a hinge adjustment brought it back to closing properly. She kept her existing door and avoided the cost of a replacement.
The lesson applies to most homes: a door that won’t close is not automatically a door that needs replacing. Hinge position and tightness are often the real cause, and checking them takes minutes. Replacing a door without checking the hinges can mean paying for new materials and labor while the same hinge problem carries over to the new door.
When is a sticking door a bigger problem?
Most sticking doors are simple. Call a professional if you notice:
Multiple doors upstairs or downstairs sticking at the same time
Diagonal cracks running from the corners of door frames into the wall
A door frame that is visibly out of square
Sloping floors near the door
Gaps between trim and the wall that are growing
Signs of moisture such as staining, soft wood, or musty odor
In older New Jersey homes, seasonal movement, past water problems, and decades of settling can all play a role. Frame problems that keep recurring usually mean moisture, framing or foundation movement, and a door adjustment alone is only a temporary fix. If you suspect structural movement, get it evaluated before cosmetic repairs.
DIY or hire a professional?
Reasonable DIY:
Tightening hinge screws
Replacing a short hinge screw with a longer one (roughly 2.5 to 3 inches) that bites into the framing behind the jamb
Cleaning paint from a hinge recess
Lubricating hinges
Running a dehumidifier
Usually better to hire:
Planing or trimming a door edge (easy to take off too much, and you can’t put wood back)
Re-hanging a door, resetting a frame, or replacing a pre-hung unit
Repairing stripped or split jamb wood
Anything involving several doors, trim damage or cracks
Painted surfaces in homes built before 1978, where sanding or planing can create lead dust. Contractors working on older painted surfaces follow EPA lead-safe work practices.
What affects the cost of a door repair
Cost depends more on the cause than the door. A hinge tune-up is quick. Costs rise with:
Whether the door must be removed and planed, re-hung or replaced
Door type (hollow-core, solid-core, paneled, pocket, bifold)
Damage to the jamb or trim that needs wood repair
Painting or finishing after the repair
Whether the root cause (moisture, settling) needs to be fixed too
How many doors are involved
Ask for a written estimate that names the cause and the proposed fix. A diagnosis that rules out a simple hinge problem first can save you the cost of a replacement you don’t need.
What to look for when hiring someone for door repair
For home repair in New Jersey, contractors who perform home improvement work must be registered with the State Division of Consumer Affairs, and registration numbers begin with “13VH.” The Division’s consumer guidance suggests asking for the registration number, verifying it with the Division, and requesting proof of liability insurance. Registration is not an endorsement, so also ask:
Is the estimate in writing, with scope, materials and cleanup described?
Do they explain the cause, not just “we’ll shave it down” or “you need a new door”?
Is there a warranty or workmanship guarantee?
Will they protect floors and clean up?
Do they have references or reviews you can verify independently?
Door not closing? Start with a proper diagnosis
If your door won’t close properly, the repair is usually simple once the cause is identified. Deft Craftsman can evaluate the door, hinges, latch and frame, and tell you whether it needs a quick adjustment or something larger. CONTACT US or call to schedule a visit anywhere in our North and Central New Jersey service area.
FAQ
Why does my door stick only in summer? Wood swells with humidity. Doors often bind during humid months and loosen in winter. Lowering indoor humidity (EPA suggests 30 to 50 percent) often helps. Avoid permanently trimming a door for a seasonal problem.
Do I need a new door if mine won’t close? Not usually. Hinge position and tightness are common causes, and a hinge adjustment can restore proper closing without replacing the door. Have the hinges, reveal and latch checked before paying for a replacement.
Can loose hinges stop a door from latching? Yes. Even slight sag shifts the latch out of line with the strike plate.
Should I plane or sand a sticking door? Only after confirming the hinges are tight and identifying exactly where it rubs. Remove material in small amounts, and seal any bare wood afterward.
Why did my door start sticking after new flooring? Thicker flooring or pad raises the floor height. The bottom of the door may need trimming, or the flooring transition may need adjusting.
Is a sticking door a sign of foundation problems? Occasionally. One door is usually hinges or humidity. Several doors, diagonal wall cracks, or visibly out-of-square frames suggest movement and warrant professional evaluation.
Can a warped interior door be fixed? Mild warping sometimes improves with humidity control or hardware adjustment. A significantly warped door usually needs replacement.
Do handymen in New Jersey need to be registered? Contractors performing home improvement work must register with the NJ Division of Consumer Affairs. Check any contractor’s status with the Division before hiring.
